How to Replace a Bathtub Yourself: Removing as well as Replacing.
How to Replace a Bathtub Yourself: Removing as well as Replacing.
Blog Article
Each person is bound to have his or her own way of thinking in relation to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately difficult task. If the old bathtub is conveniently easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will require a helper to move out the old tub and also embeded in the new one. Make sure you have actually certified yourself for the job and also fit attempting it. Rather than hiring a professional to take over a halfway-completed task, it is much better to consider employing one prior to you begin. Opportunities are you might need a professional plumber to make tube links.
This short article will aid you set up a new bath tub in your restroom if you have currently purchased a brand-new bathtub and do not need to change the setup of your previous water supply pipelines.
Your tools and also product checklist must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washers are in place between the tap as well as the sink. Safeguard the faucet in position with the producer offered backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Making use of both wood boards under its feet, position the tub in the needed position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it right into its last setting.
Preparing for the Installment
First of all, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on our other web address. Are you aware of another person who is in the market for the niche? Be sure share it. Thanks for your time invested reading it.
Information Report this page